tracksvast.blogg.se

4 strand braid
4 strand braid









4 strand braid
  1. #4 strand braid how to#
  2. #4 strand braid free#

  • Repeat Steps 4 through 13 for the braid on the other side of the charm.
  • With a length of sewing thread, tie a knot just above the half knots you tied in Step 11.
  • Then, tie one loop with ribbons 3 and 1, and one loop with ribbons 2 and 4.
  • At the end of the braid, tie one loop in center ribbons-2 and 3.
  • 4 strand braid

    They should touch, but not be stretched and distorted. You want to “lay” the ribbons in place, rather than tugging them.

    4 strand braid

    Then, repeat Steps 7 and 8 for the desired length of the braid, moving the support pin down as the work progresses. Renumber the ribbons one to four starting with the leftmost ribbon.It is helpful to place a support pin where ribbon 4 crosses over ribbon 1.

    4 strand braid

    The second movement of the braid is to move ribbon 4 over ribbon 1.The first movement is to move ribbon 1 over ribbon 2 and ribbon 3 over ribbon 4. To begin the four-stand braid, we’re going to number the ribbons one to four starting with the leftmost ribbon.I find to easiest to work on a piece of foam so I can use pins to anchor the charm and support the braid as it progresses.Depending on the length of braid that you need, you may need to adjust this 12″ length. Thread two lengths of the 12″ organdy ribbon through one of the charm holes.For my bracelet, I needed ~1¾” braid on each side. This gives you the length of braid that you’ll need-one length on each side of the charm. Subtract the length of the charms and findings from the desired finished length.Measure the total length of the charm and findings.This is the length of the finished bracelet. Measure the wrist circumference, allowing for the amount of ease desired in the finished bracelet.

    #4 strand braid how to#

    Here’s How to Make the Four-Strand Braid Bracelet: lobster claw clasp-my personal favorite, but other styles are available.These are available at most craft and hobby stores. And, you can always make your own from wooden blanks by drilling the necessary holes. It needs to have openings on each side to accommodate the ribbons. Let’s take a closer look at some of these supplies. Then, you can incorporate a four-strand braid in other projects. Here we’re going to make a bracelet to introduce you to the technique. Important as they will contribute to the largest part of the structural balance and symmetrical aesthetic stimulation of the hairstyle.Everyone’s familiar with the three-strand braid, but the four-strand ribbon braid adds a new dimension to your ribbon projects. The goal is to braid two braids one on each side of the head, that are structurally similar and on the same height. Repeat the exact same process at the opposite side of the model’s head. Remember that this clip/band will be taken out again shortly, so do whatever will be easiest to take outġ0. When you have braided the hair all the way to the tips of the length of hair, secure the braid with a clip or band. Practice the braid before attempting it on your model.ĩ. If you find that your braid doesn’t look like this, you probably braided it too tight or made a mistake during the braiding-sequence of the process. It’s important that your braid effectively There is one string that continuously runs down the middle of the braid, while the other three strands weave around this centre-strand. Of these factors will compensate the neatness and pattern of your braid.Ĩ.

    #4 strand braid free#

    It is also important that you keep your strands clearly separated and free from tangles and knots in the braiding process, as any one If you braid too tight, you’ll only end up with a messy braid. In the case of this braid you need to braid the hair in a very relaxed fashion in order to give the braid thatĭistinctive pattern. Repeat the above “over-under, under-over” process until you reach the tips of the length of the hair.











    4 strand braid